a summary or tutorial describing GPRS, General Packet Radio Service, giving
the details of the physical and logical channels.
Like other cellular systems, GPRS uses a variety of physical
and logical channels to carry the data payload as well as the signalling
required to control the calls.
GPRS physical channel
GPRS builds on the basic GSM structure. GPRS uses the same
modulation and frame structure that is employed by GSM, and in this way it is an
evolution of the GSM standard. Slots can be assigned dynamically by the BSC to
GPRS calls dependent upon the demand, the remaining ones being used for GSM
traffic.
There is a new data channel that is used for GPRS and it is
called the Packet Data Channel (PDCH). The overall slot structure for this
channel is the same as that used within GSM, having the same power profile, and
timing advance attributes to overcome the different signal travel times to the
base station dependent upon the distance the mobile is from the base station.
This enables the burst to fit in seamlessly with the existing GSM structure.
Each burst of information for GPRS is 0.577 mS in length and
is the same as that used in GSM. It also carries two blocks of 57 bits of
information, giving a total of 114 bits per burst. It therefore requires four
bursts to carry each 20 mS block of data, i.e. 456 bits of encoded data.
The BSC assigns PDCHs to particular time slots, and there
will be times when the PDCH is inactive, allowing the mobile to check for other
base stations and monitor their signal strengths to enable the network to judge
when handover is required. The GPRS slot may also be used by the base station to
judge the time delay using a logical channel known as the Packet Timing Advance
Control Channel (PTCCT).
GPRS channel allocation
Although GPRS uses only one physical channel (PDCH) for the
sending of data, it employs several logical channels that are mapped into this
to enable the GPRS data and facilities to be managed. As the data in GPRS is
handled as packet data, rather than circuit switched data the way in which this
is organised is very different to that on a standard GSM link. Packets of data
are assigned a space within the system according to the current needs, and
routed accordingly.
The MAC layer is central to this and there are three MAC
modes that are used to control the transmissions. These are named fixed
allocation, dynamic allocation, and extended dynamic allocation.
The fixed allocation mode is required when a mobile requires
a data to be sent at a consistent data rate. To achieve this, a set of PDCHs are
allocated for a given amount of time. When this mode is used there is no
requirement to monitor for availability, and the mobile can send and receive
data freely. This mode is used for applications such as video conferencing.
When using the dynamic allocation mode, the network allocates
time slots as they are required. A mobile is allowed to transmit in the uplink
when it sees an identifier flag known as the Uplink Status Flag (USF) that
matches its own. The mobile then transmits its data in the allocated slot. This
is required because up to eight mobiles can have potential access to a slot, but
obviously only one can transmit at any given time.
A further form of allocation known as extended dynamic
allocation is also available. Use of this mode allows much higher data rates to
be achieved because it enables mobiles to transmit in more than one slot. When
the USF indicates that a mobile can use this mode, it can transmit in the number
allowed, thereby increasing the rate at which it can send data.
Logical channels
There is a variety of channels used within GPRS, and they can
be set into groups dependent upon whether they are for common or dedicated use.
Naturally the system does use the GSM control and broadcast channels for initial
set up, but all the GPRS actions are carried out within the GPRS logical
channels carried within the PDCH.
Broadcast channels:
Packet Broadcast Central Channel (PBCCH): This is a downlink only channel
that is used to broadcast information to mobiles and informs them of incoming
calls etc. It is very similar in operation to the BCCH used for GSM. In fact the
BCCH is still required in the initial to provide a time slot number for the
PBCCH. In operation the PBCCH broadcasts general information such as power
control parameters, access methods and operational modes, network parameters,
etc, required to set up calls.
Common control channels:
Packet Paging Channel (PPCH): This is a downlink only channel and is used
to alert the mobile to an incoming call and to alert it to be ready to receive
data. It is used for control signalling prior to the call set up. Once the call
is in progress a dedicated channel referred to as the PACCH takes over.
Packet Access Grant Channel (PAGCH): This is also a downlink channel and
it sends information telling the mobile which traffic channel has been assigned
to it. It occurs after the PPCH has informed the mobile that there is an
incoming call.
Packet Notification Channel (PNCH): This is another downlink only channel
that is used to alert mobiles that there is broadcast traffic intended for a
large number of mobiles. It is typically used in what is termed point-to-point
multicasting.
Packet Random Access Channel (PRACH): This is an uplink channel that
enables the mobile to initiate a burst of data in the uplink. There are two
types of PRACH burst, one is an 8 bit standard burst, and a second one using an
11 bit burst has added data to allow for priority setting. Both types of burst
allow for timing advance setting.
Dedicated control channels:
Packet Associated Control Channel (PACCH): This channel is present in
both uplink and downlink directions and it is sued for control signalling while
a call is in progress. It takes over from the PPCH once the call is set up and
it carries information such as channel assignments, power control messages and
acknowledgements of received data.
Packet Timing Advance Common Control Channel (PTCCH): This channel, which
is present in both the uplink and downlink directions is used to adjust the
timing advance. This is required to ensure that messages arrive at the correct
time at the base station regardless of the distance of the mobile from the base
station. As timing is critical in a TDMA system and signals take a small but
finite time to travel this aspect is very important if long guard bands are not
to be left.
Dedicated traffic channel:
Packet Data Traffic Channel (PDTCH): This channel is used to send the
traffic and it is present in both the uplink and downlink directions. Up to
eight PDTCHs can be allocated to a mobile to provide high speed data.
|
