1 A surface height profile is given by, y = a + b sin 2 p x l (0 x l) where a, b, l are constants and x is the horizontal coordinate. The roughness of the surface, based on absolute deviation, is Options A) 2b p B) 4b p C) 6b p D) 8b p Your Answer ( Not Answered ) Correct Answer A 2 For N-bit Successive Approximation ADCs, other parameters such as clock frequency remaining constant, the conversion time is proportional to Options A) N 2 B) � N C) log N D) N Your Answer ( Not Answered ) Correct Answer B 3 The radius of a sphere is given as (40.0 � 0.5)mm. The estimated error in its mass is: Options A) � 3.75% B) � 1.25% C) � 12.5% D) � 0/125% Your Answer ( Not Answered ) Correct Answer B 4 A zero error in a vernier caliper is termed as Options A) accidental error B) interference error C) systematic error D) random error Your Answer ( Not Answered ) Correct Answer B 5 Given the discrete-time sequence x[n] = [2, 0, -1,-3, 4, 1, -l, X(e j p ) is Options A) 8 B) 6 p C) 8 p D) 6 Your Answer ( Not Answered ) Correct Answer C 6 Linear variable differential transformer has Options A) two primary coils connected in phase and a secondary coil B) two primary coils connected in opposition and a secondary coil C) one primary coil and two secondary coils connected in phase D) one primary coil and two secondary coils connected in opposition Your Answer ( Not Answered ) Correct Answer D 7 Position sensor units having a constant sensitivity of lV/mm are used for feedback in number of position controlled system units, each having an overall forward path dc gain of 50. If the random dc bias errors in the outputs of various sensor units are characterized as normal with mean 0 and standard deviation ( s ) 0.01V, for a constant set point of 5V, the true position outputs of the various controlled system units can be characterized as normal with Options A) mean of 5.0, s of 0.01 B) mean of 0.0, s of 0.01 C) mean of 5.0, s of 0.0098 D) mean of 4.902, s of 0.0098 Your Answer ( Not Answered ) Correct Answer C 8 The refractive index of the core of an optical fiber is n 1 and that of the cladding is nf If (n 1 � n 2 ) = D n, then the fiber can be made single mode with numerical aperture unchanged by Options A) reducing core diameter and increasing D n B) reducing both core diameter and D n C) reducing core diameter alone D) reducing D n alone Your Answer ( Not Answered ) Correct Answer D 9 For a suppressed carrier amplitude modulator (AM-SC) system, the carrier and the modulating inputs are x c (t) = cos w c t and x m (t) = 0.5 sin w m t, respectively. The output of the system is proportional to Options A) sin ( w c + w m ) t � sin ( w c - w m ) t B) sin ( w c + w m ) t + cos ( w c - w m ) t C) (1 + 0.5 sin w m t) cos w c t D) (1- 0.5 sin w m t) cos w c t Your Answer ( Not Answered ) Correct Answer B 10 The 3-dB cut-off frequency of a first analog high pas filter is w c the output will have a phase shift of Options A) - p 2 B) - p 4 C) p 2 D) p 2 Your Answer ( Not Answered ) Correct Answer B 11 In an INTEL 8085 microprocessor the ADDRESS-DATA bus and the DATA bus are Options A) Non multiplexed B) Multiplexed C) Duplicated D) Same as CONTROL bus Your Answer ( Not Answered ) Correct Answer B 12 A 3 � digit nultimeter has an accuracy specification of (� 0.5% of reading � 5 counts). If the meter reads 2.00 mA on a full scale of 20mA, the worst-case error in the reading is Options A) 0.5% B) 2.5% C) 3.0% D) 5.5% Your Answer ( Not Answered ) Correct Answer C 13 The measurements of a source voltage are 5.9V, 5.7V and 6.1V. The sample standard deviation of the readings is Options A) 0.013 B) 0.04 C) 0.115 D) 0.2 Your Answer ( Not Answered ) Correct Answer D 14 Consider the following systems: System 2: G(s) = 1 2(2s+1) System 1: G(s) = 1 2(5s+1) The true statement regarding the system is Options A) Bandwidth of system 1 is greater than the bandwidth of system 2 B) Bandwidth of system 1 is lower than the bandwidth of system 2 C) Bandwidth of both the systems are the same D) Bandwidth of both the systems are infinite Your Answer ( Not Answered ) Correct Answer A 15 The transfer function of a system is A s 2 + w 2 The steady-state gain of the system to a unit-step input is Options A) A w 2 B) 0 C) � D) not possible to be determined Your Answer ( Not Answered ) Correct Answer C 16 In 8085 microprocessor, CY flag may be set by the instruction Options A) SUB B) INX C) CMA D) ANA Your Answer ( Not Answered ) Correct Answer A 17 V 1 and V 2 are the input voltages of an instrumentation amplifier. The output of the instrumentation amplifier is found to be 100(V 1 � V 2 ) + 10 -4 (V 1 + V 2 ). The gain and the common mode rejection ratio (CMRR) of the instrumentation amplifier respectively are Options A) (50, 60 dB) B) (50, 120 dB) C) (100, 60dB) D) (100, 120 dB) Your Answer ( Not Answered ) Correct Answer C 18 The sequence x[n] whose z-transform is X[z] = e (1/Z) is Options A) 1 n! u[n] B) 1 -n! u[-n] C) (-1) n 1 n! u[n] D) 1 -(n+1)! u[-n-1] Your Answer ( Right Answer ) 19 The time taken by an ionized atom, of mass m kg and charge e Coulombs, pulsed into a field-free region with V volts, to reach a detector L meters away is Options A) 1 L � m 2eV B) L � m 2eV C) m � L 2eV D) 2 L � m 2eV Your Answer ( Not Answered ) Correct Answer B 20 The clock frequency of a timer-counter is 10MHz. The timer-counter is used in the period mode and the input to the timer-counter is a square wave of frequency 2 kHz. The display of the timer-counter will show a value Options A) 200 B) 2000 C) 5000 D) 50000 Your Answer ( Not Answered ) Correct Answer C |
